How to Wire a Jon Boat. Jon Boat Wiring Guide – Flat Bottom Boat World

Rate this post

When you buy a new Jon boat it is usually just a shell. But even after you have bought a new outboard motor to power your boat your job is not yet done. Not only do you need to wire your trolling motor to a battery but if you plan to navigate waters at night you may need to wire up navigational lights as well. If you include fishfinders, search lights and other electronic goodies to your build then the wiring of your Jon boat can start to seem like a messy and daunting task. Not to worry we are here to show you the basics of wiring your boat.


  • Power is a critical upgrade for a functional Jon boat
  • Stay safe!
  • Key principles for wiring your Jon boat
  • Hiding wires in your Jon boat
  • Ensure that your Jon boat electrics are properly protected
  • Videos and resources for successful Jon boat wiring

Power is a critical upgrade for a functional Jon boat

If you are ready to do more with your Jon boat than resting on your oars, you will need to add power to your set-up.

Obviously the most common component on a Jon boat that requires power is the trolling motor. But depending on the use of your Jon boat there are a wide variety of other components and accessories that may need to be battery powered.

These include:

  • Navigation lights.
  • Deck lighting and accessory lights.
  • Bilge pump.
  • GPS.
  • Fish finders and Sonar.
  • Control panels.
  • On-board power banks and charging points.

Simultaneously connecting a range of items that a Jon boat needs to perform well for recreational boating, angling or hunting requires some basic electrical knowledge as well as a sound and logical approach to wiring your boat.

There are various approaches you can take for your Jon boat wiring set-up, and the approach you take will depend on your resources, the equipment and tools you have to hand and the functionality you want to achieve.

Stay safe!

The most important thing to keep in mind before you start any electrical work on your boat is that electric is dangers even from a relatively small 12 V battery. This is never more important than it is on a boat where you will be surrounded by water.

Boat wiring must be 100% protected from the elements as water is an electrical conductor – electric and water don’t mix well!

Untidy, piecemeal patch wiring jobs are dangerous and carry the risk of damage to your equipment, can start fires or even cause bodily harm or a fatality from electrocution.

55% of US Coastguard investigated boat fires are caused by faulty wiring. So, it is critical that you get the wiring of your boat right.

We have provided this information to give you an approach for wiring your boat effectively. We strongly advise calling a professional marine electrician or surveyor if you feel out of your depth and also to use an electrician to review and ensure that the work you have undertaken yourself is electrically sound.

Key principles for wiring your Jon boat

In this article we will outline key points and principles for basic wiring of your Jon boat with inclusion of a control panel to keep everything organized.

Wiring your Jon boat is as simple as following a wiring diagram.

However you need to be aware of how to insulate and protect your electrical wires and connections before you begin.

We have included a video for wiring a Jon boat and several electrical wiring diagrams as well as links to some excellent additional resources These will assist you in accomplishing this task more effectively.

There is also a list of key pieces of kit that you will need to complete the job and also that will give a more resilient finish to your work.

Items you will need to wire your Jon boat:

  • A battery. Ideally you should have 2 batteries though for light electrical loads 1 battery will probably suffice.
  • A main battery switch.
  • A control panel.
  • A reel of marine grade primary wire 8-14 AWG depending on the size of your boat.
  • A negative bus bar.
  • Waterproof in-line fuses.
  • Spiral wrap or wire conduits.
  • Wire ties.
  • Wire tie mounts.
  • Marine-grade butt connectors.
  • Heat shrink wire wrap.

In addition you will need a regular selection of tools including a pencil or marker, wire cutters, pliers, drill, screwdrivers, a heat gun, hole saw and handheld power saw.

Protective eye-wear, gloves and a face-mask are also advisable.

Wiring a Jon boat can appear to be a daunting task when you first approach it but with careful planning and a good guide you can wire your boat in a single evening.

Plan and organize your Jon boat wiring set-up

  • You will need to sketch out or acquire a simple wiring plan for your boat which outlines the layout of the circuitry that needs to be connected. This will help in planning the equipment you need, wire lengths and key connections in your boat wiring. We have included several wiring layout diagrams at the end of this article.
  • Ensure you identify and distinguish your positive (usually red) and negative (typically black) terminals on your battery, the control panel, and all the accessories that will become part of your Jon boat wiring set-up. Match like with like at all times.

Key points for wiring a boat switch panel

  • Power runs from your onboard battery to your control panel from which the power will be distributed to your connected equipment. The switches on the control panel essentially act as circuit-breakers that cut off power to the equipment that is not in use.
  • You will need to correctly position all accessories and boat equipment, that is to be wired, in the correct place on your boat so you can run adequate lengths of your marine cabling to them. For example, if you are connecting a deck light make sure you position the light in the exact location on the deck where it will be used before you connect it to the battery or you may find that the cable you allocated for the connection is too short!
  • Lay out and cut all the relevant lengths of cable on the boat according to your set-up diagram. How many cables do you need? Cut that amount making sure you have enough length in each cable.
  • When working with marine grade wire, have plenty on hand, and leave slack in your work for re-positioning, making corrections, upgrades and for making your final connections.
  • It may be helpful to approach dealing with all positive wiring first and once that is completed focusing on the negative wiring connections afterwards.
  • Your control panel will have connectors that allow you to splice wiring from your equipment into the control panel. You will need to attach complementary connectors to all wiring coming from your Jon boat equipment.
  • Wire ends should be connected with appropriate marine-grade butt connectors. Install these heat shrink terminals using a heat gun to create a watertight seal. Heat shrink wire wrap can also be used to group wires together if needed.
  • The connectors you use must be marine grade (corrosion resistant) and match the gauge of wire you are working with.
  • A negative bus bar is used prior to connection of the negative wiring to the negative battery terminal to handle your boat’s negative load.

Hiding wires in your Jon boat

Masses of tangled and improperly connected wires are not only unsightly, they are dangerous!

Once you have established your wiring arrangement you can hold all your wiring together using a flexible wiring conduit of appropriate length. You can also use cable ties and cable tie mounts.

In keeping with The American Boat and Yacht Council recommendation make sure electrical wires are secured at a minimum of at least every 18 inches.

Ensure that your Jon boat electrics are properly protected

  • Avoid overloading your writing, as this can cause short circuiting and fires.
  • Fuses and circuit breakers should be sized below the amp rating of the equipment and accessories that are being protected. The American Boat and Yacht Council advises that they should be located within 7 inches of wire length from your power source.
  • Do not use wire nuts for connections in your boat wiring, use ring or spade terminals with heat shrink tubing.

Insulating wires in a Jon boat

BC-5W2 is specialist marine wire that offers a suitably high level of insulation and quality stranded tinned copper wire within it. This wire is specifically manufactured to withstand the corrosive and abrasive environment experienced on boats.

Electrical tape, sleeves, padding and seals can also be used to insulate and protect your wiring, especially if it is run behind the ribs of the boat.

Videos and resources for successful Jon boat wiring

Video with easy practical steps for wiring a Jon boat

This is a relaxed run-through of the key steps you need to take to successfully wire your Jon boat.

Additional resources that will help you build up knowledge on boat wiring

Organizations to contact to learn more

  • The American Boat and Yacht Council provides industry standards and education resources for wiring recreational vessels.

Wiring diagrams

In conclusion

If you are used to DIY projects on your Jon boat, wiring is going to be a task you will have to encounter at some point.

Despite the apparent simplicity of Jon boat wiring, safety is always paramount and getting assistance from a professional or at least a boater who is experienced in marine wiring is prudent.

Once you have mastered the principles of safe wiring, the scope of your projects and the performance of your boat will increase massively.

You are viewing this post: How to Wire a Jon Boat. Jon Boat Wiring Guide – Flat Bottom Boat World. Information curated and compiled by along with other related topics.


Please enter your comment!
Please enter your name here